In this article
Choosing EPDM or FKM for a PG25 cooling loop is not a contest between polymer names. The useful comparison is between identified seal compounds exposed to an identified coolant under relevant conditions. For a VeriClean Seals™ specification, keep coolant compatibility, mechanical aging, and initial surface cleanliness as separate qualification questions.
1. What does PG25 mean on this purchase order?
PG25 often denotes an approximately 25% propylene glycol solution in water, but the label alone does not establish the concentration basis or formulation. Ask whether the percentage is by weight or volume and whether it describes glycol itself or a diluted commercial concentrate. OCP’s July 2026 PG25 base specification requires 25–28% propylene glycol by weight; that is not a requirement for exactly 25% by volume.
Identify the coolant manufacturer, product designation, concentration tolerance, inhibitor technology, and relevant pH specification. Request formulation-specific compatibility guidance without demanding a proprietary additive recipe. OCP explicitly states that compliant fluids from different suppliers are not necessarily interchangeable or functionally equivalent. A report for one PG25 product should not silently qualify another.
2. Which EPDM or FKM compound is actually supplied?
EPDM is ethylene propylene diene rubber; FKM is a fluorocarbon elastomer family. Neither designation identifies the complete compound. OCP’s coolant guidance notes that curing agents, plasticizers, and other formulation differences can change suitability. Request a traceable manufacturer compound identifier, nominal hardness and tolerance, and cure-system information relevant to the application. Matching polymer labels and hardness values does not establish matching performance.
OCP lists both EPDM and FKM among commonly used PG25 materials, while treating that list as a starting point. It recommends peroxide-cured EPDM and cautions that sulfur-cured EPDM can introduce sulfate into the fluid over time. That is a specific question for the supplier—not proof that every peroxide-cured EPDM passes, or that FKM is unsuitable.
3. Does the comparison fit this coolant application?
A general chemical-resistance rating can help shortlist compounds, but it cannot select a universal winner. Parker’s engine-sealing guidance describes purpose-developed coolant-resistant FKM grades. This demonstrates why a generic FKM designation can hide important differences. Its engine-coolant evidence does not establish performance in a particular PG25 cold-plate loop, and its temperature claims should not be transferred to that application.
Ask what fluid and inhibitor package supported the supplier’s recommendation. Was it the proposed PG25 product, another glycol mixture, or an automotive coolant? Require the exposure temperature and duration. Compare candidate compounds under matching conditions; otherwise, apparent differences may reflect different test environments rather than a useful EPDM-versus-FKM comparison.
References: Parker: Coolant Resistant FKM Materials Designed for Extreme Performance in Engine Design · OCP Guidelines for Using Propylene Glycol-Based Heat Transfer Fluids in Liquid Cooled Racks, Revision 2.0, September 2026
4. What changed after coolant exposure?
Request before-and-after results for volume change, including swell or shrinkage, and hardness change. Mass, tensile strength, and elongation results can add context. ASTM D471 provides comparative liquid-exposure methods covering these properties. Specify the actual fluid concentration, compound identity, specimen preparation, temperature, duration, and measurement method so the results can be interpreted rather than reduced to a single compatibility score.
OCP recommends confirmation at the system’s maximum operating temperature and supplier-guided exposure conditions. Agree on acceptance limits with the component manufacturer before testing; limits depend on the application. ASTM cautions that accelerated exposure results may not directly correlate with actual part performance. A completed soak test is evidence about the tested conditions, not an automatic service-life guarantee.
References: ASTM D471-16a(2021): Standard Test Method for Rubber Property—Effect of Liquids, Public Scope and Significance · OCP Guidelines for Using Propylene Glycol-Based Heat Transfer Fluids in Liquid Cooled Racks, Revision 2.0, September 2026
5. Will the aged seal still perform under compression?
Liquid-exposure results do not by themselves establish sealing performance under sustained compression. Compression set measures permanent deformation after compressive loading; it addresses a different question from swell or hardness. OCP references ASTM D395 for compression-set assessment and ASTM D1414 for O-ring testing. Ask whether available evidence covers the proposed compound and the conditions relevant to its sealing duty.
Clarify the test medium, compression conditions, temperature, duration, and recovery procedure. Do not treat an air-aging result as an actual-coolant result. For a quick disconnect or other assembled component, ask the manufacturer what leak and cycling evidence is needed beyond coupon testing. The qualification must address the component’s function, not merely whether an uncompressed sample survived immersion.
References: OCP Guidelines for Using Propylene Glycol-Based Heat Transfer Fluids in Liquid Cooled Racks, Revision 2.0, September 2026 · ASTM D471-16a(2021): Standard Test Method for Rubber Property—Effect of Liquids, Public Scope and Significance
6. What does initial cleanliness prove—and not prove?
Initial surface cleanliness concerns contamination present when the seal enters the system. It does not establish long-term resistance to coolant, or retention of mechanical properties. Keep the specified cleanliness evidence separate from the aging report. OCP likewise addresses commissioning cleanliness separately from wetted-material compatibility and post-exposure fluid analysis.
A compound may also affect fluid condition during exposure through extractables or degradation products. OCP recommends fluid controls to distinguish material-related effects from changes caused by heating the coolant alone. Ask whether the evaluation includes fluid-condition evidence where that matters to the loop. For Pacific Rubber & Packing’s VeriClean Seals™, document the three questions separately: initial contamination, coolant interaction, and mechanical aging. None substitutes for the others.
Qualify the compound–coolant pair
Select EPDM or FKM using evidence for the exact compound, PG25 formulation, and operating conditions. Keep swell and hardness results, compression-set evidence, and initial cleanliness documentation distinct. Neither the polymer label nor the PG25 label is a qualification by itself.
Sources & further reading
- OCP Base Specification for Single-Phase Propylene Glycol-Based Cold Plate Coolants (PG 25), Version 1.0.0, July 2026
- OCP Guidelines for Using Propylene Glycol-Based Heat Transfer Fluids in Liquid Cooled Racks, Revision 2.0, September 2026
- Parker: Coolant Resistant FKM Materials Designed for Extreme Performance in Engine Design
- ASTM D471-16a(2021): Standard Test Method for Rubber Property—Effect of Liquids, Public Scope and Significance
AI-assisted editorial prepared from the cited engineering references. This article is not a compatibility approval, cleanliness certification, or substitute for equipment-specific qualification.
About the publisher
Pacific Rubber & Packing is the company behind VeriClean Seals™. Liquid Cooling Insights connects public engineering references with practical questions about wetted components and seal qualification.
Meet Pacific Rubber & Packing