In this article
A seal cleanliness report should let you answer a practical question: what contamination was measured, on which parts, under what conditions? A total particle count or a statement that parts were cleanroom processed cannot answer that alone. Request the measurement record behind the conclusion so engineering and purchasing can evaluate the same evidence.
1. Which parts and surfaces were actually tested?
Ask for the part number and revision, material or compound identification, production lot, sample identifiers, test date, and number of seals tested. The report should distinguish the production lot from the inspection sample and state whether seals were extracted individually or pooled into one analysis.
Define the inspected surface: the complete seal, selected sealing faces, or another agreed area. Request the sampled area when results are area-normalized, together with any masking or preparation. ISO 16232 addresses road-vehicle component particulate inspection; if its framework is used for your seal application, identify the agreed method and edition rather than treating the standard name as a universal seal certification.
References: ISO 16232:2018 — Road vehicles — Cleanliness of components and systems: public scope and abstract · VDA QMC — VDA 19.1 Inspection of Technical Cleanliness, 2025 Yellow Volume: publicly available draft
2. Was particle extraction qualified and background controlled?
Request the extraction technique, test medium, relevant operating parameters, filtration details, and analytical method. Ask for qualification evidence showing that the procedure removes the relevant contamination adequately. Repeated extractions with a declining particle load can support extraction qualification; equipment particle-recovery checks and final-rinse checks address additional losses. These are complementary checks, not interchangeable assurances.
Request the procedural blank result, its acceptance basis, and whether any correction was applied. A blank measures contamination introduced by the test setup and handling rather than the seal. Also ask for the method’s lower reportable particle size, detection limitations, and deviations. With elastomers, the laboratory should address whether extraction conditions could attack the material and generate particles. VDA’s public 2025 draft discusses these controls; specify the governing edition in your purchase requirements.
References: VDA QMC — VDA 19.1 Inspection of Technical Cleanliness, 2025 Yellow Volume: publicly available draft
3. Are size bands and normalization units explicit?
Ask for particle counts in defined size bands, with boundaries in micrometers and the sizing convention identified. Establish whether the figures are counts within each band or cumulative counts above a size. A cleanliness code alone should not replace the underlying distribution.
Request the absolute counts for the inspection sample alongside normalized results. Counts per seal and counts per 1,000 cm² describe different bases; volume-based reporting needs its own defined reference. A pooled per-seal result is an average, not proof that each seal carried that count. Results below the method’s reportable range are unmeasured, not automatically zero.
References: VDA QMC — VDA 19.1 Inspection of Technical Cleanliness, 2025 Yellow Volume: publicly available draft
4. What was the largest particle, and what could the method identify?
Request the largest detected particle’s measured dimensions and an image with scale information. Clarify whether fibers are included, reported separately, or excluded from the agreed particle categories. These details can reveal concerns that a single total count hides.
Ask for metallic and nonmetallic results only when the analytical method supports that distinction. Optical metallic-shine classification is not definitive material identification: some metals lack shine, and some nonmetals appear shiny. Scanning electron microscopy with energy-dispersive X-ray spectroscopy can add elemental composition information. The report should state which particles received that analysis and its limitations, rather than imply that every counted particle was chemically identified.
References: VDA QMC — VDA 19.1 Inspection of Technical Cleanliness, 2025 Yellow Volume: publicly available draft · Thermo Fisher Scientific — Understanding Technical Cleanliness
5. How does the sample support lot acceptance?
Ask how samples were selected, how frequently testing occurs, and whether the report documents initial qualification, routine monitoring, or lot release. Agree on sample quantity, pooling rules, acceptance criteria, and the response to a failed or invalid test before interpreting a pass statement. A favorable sample result does not establish that every seal in a production lot is identical.
There is no universal seal cleanliness threshold in ISO 16232. It explicitly leaves component-specific limits to application-informed specialists. Set requirements around the receiving system’s sensitivity, operating conditions, and feasible controls—not an unexplained supplier grade or a numerical limit borrowed from an unrelated component.
References: ISO 16232:2018 — Road vehicles — Cleanliness of components and systems: public scope and abstract · VDA QMC — VDA 19.1 Inspection of Technical Cleanliness, 2025 Yellow Volume: publicly available draft
6. At what handling and packaging stage was cleanliness measured?
Ask whether the sample was tested immediately after cleaning, after packaging, or after shipment and unpacking. Record package condition, opening practices, storage interval, and any pre-test cleaning. Clarify whether packaging was included in the extraction or excluded. A result for freshly cleaned seals does not directly describe their condition after subsequent handling.
ISO Class 7 concerns airborne particle concentration in the cleanroom environment. Processing there does not certify a seal’s particulate burden or establish an ISO 14644-9 surface cleanliness class. ISO 14644-9:2022 concerns assessment of particle concentration on solid surfaces, including products. Request product measurement evidence separately from cleanroom classification evidence.
References: VDA QMC — VDA 19.1 Inspection of Technical Cleanliness, 2025 Yellow Volume: publicly available draft · ISO 14644-9:2022 — Assessment of surface cleanliness for particle concentration: public scope and abstract
7. Which cleanliness questions remain unanswered?
Keep particle, extractables, and microbial results separate. Particle counts do not establish chemical extractables: ISO 16232 excludes filmy contamination, and a particle extraction is not automatically a chemical-extractables study. If chemical release matters, request a separately defined chemical test with its exposure conditions and analytical scope.
Likewise, particle measurements do not demonstrate microbial cleanliness; ISO 14644-9 excludes microbiological state. Request the relevant microbial test separately. Initial cleanliness also cannot prove resistance to PG25 aging. That requires application-relevant exposure and performance evidence, not an inference from a clean starting surface.
References: ISO 16232:2018 — Road vehicles — Cleanliness of components and systems: public scope and abstract · ISO 14644-9:2022 — Assessment of surface cleanliness for particle concentration: public scope and abstract
Request evidence you can compare
A useful supplier report connects an identified sample to a qualified method, explicit results, and an agreed acceptance basis. Define those requirements before purchase, and keep environmental, particle, chemical, microbial, and aging evidence distinct.
Sources & further reading
- ISO 16232:2018 — Road vehicles — Cleanliness of components and systems: public scope and abstract
- VDA QMC — VDA 19.1 Inspection of Technical Cleanliness, 2025 Yellow Volume: publicly available draft
- Thermo Fisher Scientific — Understanding Technical Cleanliness
- ISO 14644-9:2022 — Assessment of surface cleanliness for particle concentration: public scope and abstract
AI-assisted editorial prepared from the cited engineering references. This article is not a compatibility approval, cleanliness certification, or substitute for equipment-specific qualification.
About the publisher
Pacific Rubber & Packing is the company behind VeriClean Seals™. Liquid Cooling Insights connects public engineering references with practical questions about wetted components and seal qualification.
Meet Pacific Rubber & Packing